|STEEL WIRE ARMOURED FIRE RESISTANT HALOGEN FREE POWER CABLES||Technical Data sheet
NHXHRHX FE180 PH90/E90 0,6/1 kV and NHXHRHX-J FE180 PH90/E90 0,6/1 kV fire resistant and halogen free power cables, are intended for power supply to fire protection equipment in objects of sharp fire protection requirements, particularly in fire alarm and fire automatic control systems.
The cables shall be applied in locations where, in case of fire, higher safety for human beings and expensive electronic equipment is required.
Functions of the cables are maintained – power is supplied to equipment which must operate in fire conditions and during fire fighting (e.g. water pumps in fire extinguishing systems, smoke removing fans, emergency lighting and elevators).
The cables are certified by Scientific and Research Centre for Fire Protection - National Research Institute (Centrum Naukowo-Badawcze Ochrony Przeciwpożarowej - PIB) at Józefów.
The cables are flame retardant and their smoke emission is low, emitted fumes are non toxic and non corrosive.
The cables are resistant to water in accordance with EN 50200 Annex E and can be used in fire protected rooms with fixed pressure water spraying fire extinguishing systems (sprinkler zones).
Galvanized steel wire armour provides carrying an axial load of the cable during installation and exploitation. It also offers enhanced protection against mechanical damages and rodent attack, as well as shielding properties.
The cables are oil-resistant and designed for frequent contact with petroleum products, as in petrol stations and stores, where engine fuels and lubricants are pumped or handled.
The cables are suitable for fixed indoor and outdoor installations also for direct earth burial. Cables are UV radiation resistant.
- bare annealed copper conductors meeting requirements of PN-EN 60228 standard:
RE - class 1 single wire round conductor,
RM - class 2 multiwire round conductor,
- mica tape and halogen free cross-linked compound insulation – colours:
- up to 5 wires in accordance with PN-HD 308,
above 5 wires black and white conductor number printed on it,
green-yellow protective conductor in the outer layer in NHXHRHX-J FE180 PH90/E90 0,6/1 kV cable,
- insulated conductors laid-up into a cable core,
- inner covering made of halogen free compound,
- cable sheath made of halogen free compound,
- galvanized steel wire armour,
- orange cable covering made of cross-linked halogen free compound, (oxygen index bigger than 35%).
Operating voltage 0.6/1 kV
Voltage test 4.0 kV rms
Insulation resistance at 90°C, minimum 1011 Ω·cm
Inductance, approximate 0.7 mH/km
Conductor temperature limit
in work conditions +90°C
in short-circuit +250°C
Corrosivity of emitted gases per PN-EN 60754-1, PN-EN 60754-2, IEC 60754-2
pH, approximate 6.8
conductivity, approximate 0.4 µS/mm
Smoke density per PN-EN 61034-2, IEC 61034-2
light transmittance, minimum 70%
Operating temperature range
during operation from -30 to +90°C
during installation from -5 to +50°C
Minimum bending radius
single core cables 15 x cable diameter
multi core cables 12 x cable diameter
Cable combustibility fire resistant
Combustibility tests PN-EN 60332-1-2, IEC 60332-1-2, PN-EN 60332-3-24, IEC 60332-3-24 (cat. C)
Circuit integrity *
E90 DIN 4102-12
PH90 PN-EN 50200 Annex or PN-EN 50362
Insulation integrity FE180 IEC 60331-21, IEC 60331-11
Reference standards AT-0603-0496/2016, WT-TK-44, DIN VDE 0266, PN-HD 604 S1
*Circuit integrity is dependent on installation method.
Cable installation - Only certified cable fixing systems shall be used. Systems certified according to DIN 4102 part 12 are recommended.
The cable meets requirements of the low voltage directive 2014/35/EU
Other cross-sections and conductor counts available on request.
TECHNOKABEL S.A. reserves the right to change specifications without prior notice.