acrobat reader_50x50  


EISF and EIFA instrumentation cables are intended for control and instrumentation circuits, for signal, monitoring and data processing systems and for analogue or digital data transmission, all in industrial electronics applications, allowing particularly for conditions met in chemical, petrochemical and paper industries.

The cables are protected by an overall electrostatic shield against external electric interferences.

Shielded pair structure substantially decreases mutual influence between signals transmitted along the cable.

Steel tape armour in EIFA cables offers enhanced protection against mechanical damages and rodent attack.

The cables can also be used for power supply to small auxiliary devices on condition that current-carrying capacity limit (see our Technical Guide) is not exceeded.

The cables are suitable for fixed indoor and outdoor installations.

Sheathing PVC of high oxygen index is UV radiation and weather resistant, is self-extinguishing and flame retardant. The cables pass combustibility test according to PN-EN 60332-3 standard.

The cables are oil-resistant and offer enhanced resistance to aliphatic hydrocarbons.


-   bare annealed copper wire conductors,

            05 – 0.50 mm2 (1x0.8 mm),

              09 – 0.88 mm2 (7x0.4 mm)

              15 – 1.50 mm2 (7x0.52 mm),

-   heat resistant PVC insulation,

-   insulated conductors twisted into:

            pairs IP - colour code insulation: white and red,

            triads IT - colour code insulation: white, red and blue,

-   pair/triad electrostatic shield incorporating aluminium-polyester tape and stranded annealed tinned copper drain wire, cross-section 0.22 mm2 (7x0.2 mm),

-   special PVC sheath of shielded pairs/triads, blue (RAL 5012), other colours also available and printed black number of pair or triad,

-   shielded and sheathed pairs or triads laid-up in layers,

-   cable core wrapped in polyester tape,

-   overall electrostatic shield incorporating aluminium-polyester tape and stranded annealed tinned copper drain wire, cross-section 0.22 mm2 (7x0.2 mm), number of drain wires from 1 to 3 depending on the cable core diameter,

-   special PVC cable sheath, blue (RAL 5012), other colours also available,

-   steel tape armour for EIFA cable,

-   special PVC cable covering, blue (RAL 5012), other colours also available.


DC loop resistance at 20°C ,maximum:

      0.50 mm2 conductor                     75.0 Ω/km

      0.88 mm2 conductor                     42.8 Ω/km

      1.50 mm2 conductor                     24.2 Ω/km

Resistance unbalance, maximum:

      0.50 mm2 conductor                     1.120 Ω/km

      0.88 mm2 conductor                     1.070 Ω/km

      1.50 mm2 conductor                     0.605 Ω/km

      conductor/conductor                    1500 V rms

      conductor/screen                         1000 V rms

Operating voltage Uo/U    300/300 V

Voltage test
    conductor/conductor    1500 V rms
    conductor/screen         1000 V rms

Insulation resistance, minimum     500 MΩ·km

Mutual capacitance, maximum:

      0.50 mm2 conductor                     210 nF/km

      0.88 mm2 conductor                     230 nF/km

      1.50 mm2 conductor                     220 nF/km

Operating temperature range
      during operation                    from - 30 to + 90°C
      during installation                   from   - 5 to + 70°C

Minimum bending radius              15 x cable diameter

Resistance to aliphatic hydrocarbons          NF M 87-202 Annex A

Oil resistance                               PN-EN 60811-404

Cable combustibility                     flame retardant

Combustibility tests                     PN-EN 60332-1-2, IEC 60332-1-2

Reference standards                    NF M 87-202


The cable meets requirements of the low voltage directive 2014/35/EU

Other cross-sections and pair, triad or quad counts available on request.

TECHNOKABEL S.A. reserves the right to change specifications without prior notice.