FIRE RESISTANT HALOGEN FREE MOTOR SUPPLY CABLES Technical Data sheet
 

 

 acrobat reader_50x50  

APPLICATIONS

(N)HXCH-J SERVO FE180 PH90/E90 0,6/1 kV fire resistant halogen free cables, are intended for connecting converters or inverters with motors in fire protection equipment which is to operate in fire conditions.

The cables shall be applied in locations where, in case of fire, higher safety for human beings and expensive electronic equipment is required.

Functions of the cables are maintained – power is supplied to equipment which must operate in fire conditions and during fire fighting (e.g. water pumps in fire extinguishing systems, smoke removing fans, emergency lighting and elevators).

The cables are certified by Scientific and Research Centre for Fire Protection - National Research Institute (Centrum Naukowo-Badawcze Ochrony Przeciwpożarowej - PIB) at Józefów.

The cables are flame retardant and their smoke emission is low, emitted fumes are non toxic and non corrosive.

Cables are protected by a specially designed and highly effective collective shield against emission of electromagnetic interferences to environment and against influence of external interferences.

The cables are suitable for fixed indoor and outdoor installations. UV radiation protection is required for outdoor installations. Laying cables in water or direct earth burial are only permitted if additional protection is used.

CONSTRUCTION                                                                                                           

- flexible, multiwire conductors, stranded of bare annealed copper wires (tin-plated on request), meeting requirements of class 5 per PN-EN 60228,

- double special cross-linked silicone rubber insulation - colours of insulation: black, brown, grey, green-yellow,

- insulated conductors and fillers laid-up in a cable core,

-  cable core wrapped in polyester tape,

-  cable core wrapped in mica tape,

- double screen incorporating aluminium-polyester tape under a tinned copper wire braid shield of coverage bigger than 80%,

- orange cable sheath made of halogen free compound type HM4 according to HD 604 S1 and VDE 0276-604, (oxygen index bigger than 35%).

CHARACTERISTICS

Operating voltage    0.6/1 kV

Voltage test    4.0 kV rms

Insulation resistance at 90°C, minimum   1011 Ω·cm

Inductance, approximate    0.7 mH/km

Shielding efficiency, approximate    75 dB

Conductor temperature limit
    in work conditions          +90°C
    in short-circuit               +250°C

Operating temperature range
      during operation             from -30 to +90°C
      during installation           from   -5 to +50°C

Minimum bending radius       15 x cable diameter

Corrosivity of emitted gases per    PN-EN 60754-1, PN-EN 60754-2, IEC 60754-2

pH, approximate    6.8

conductivity, approximate    0.4 µS/mm

Smoke density per    PN-EN 61034-2, IEC 61034-2

light transmittance, minimum    70%

Cable combustibility             fire resistant

Combustibility tests             PN-EN 60332-1-2, IEC 60332-1-2, PN-EN 50266-2-4, IEC 60332-3-24 (cat. C)

Circuit integrity *                           

             E90                     DIN 4102-12

             PH90                   PN-EN 50200 or PN-EN 50362

Insulation integrity FE180       IEC 60331-21, IEC 60331-11

Reference standards             AT-0603-0495/2016, WT-TK-44, DIN VDE 0266, PN-HD 604 S1

*Circuit integrity is dependent on installation method.

Cable installation - Only certified cable fixing systems shall be used. Systems certified according to DIN 4102 part 12 are recommended.

The cable meets requirements of the low voltage directive 2014/35/EU

Other cross-sections and conductor counts available on request.

TECHNOKABEL S.A. reserves the right to change specifications without prior notice.